There is no single Advantage+ switch in a leads campaign. Meta counts a campaign as Advantage+ when three settings are on together: Advantage+ campaign budget, Advantage+ audience and Advantage+ placements. Narrow any one of them and that section of Ads Manager reads Advantage+ off, which is the only switch Meta offers.
What makes a leads campaign count as Advantage+
Meta’s help article on what turns Advantage+ on and off gives each lever its own condition. Ads Manager applies the setup when you pick the Leads objective, and you can see the state per section and, on the right of the screen, in the Campaign opportunities panel at campaign and ad set level.
| Lever | What Meta automates | Advantage+ turns off when |
|---|---|---|
| Budget | one campaign budget, split across ad sets | the campaign runs two or more ad sets on ad set budgets |
| Audience | your targeting becomes a suggestion and ads can reach beyond it | you choose Further limit the reach of your ads and uncheck Use as a suggestion |
| Placements | every available placement is eligible | you exclude a placement in an ad set, or opt out of mobile or desktop devices |
None of the three touches the lead itself. Instant forms, website forms, calls and click to message lead ads all stay available, the performance goal stays on leads or conversion leads, and the creative is built exactly as before. The automation only decides where the money goes, who sees the ad and in which placements.
Steps to turn it off
- Name the constraint first. Retargeting, or a placement whose leads never qualify, are the two reasons that survive a second look at the numbers.
- For budget, set the budget strategy to ad set budget and keep at least two ad sets in the campaign. This is the same choice as CBO vs ABO, read in the other direction: you take the split back from Meta.
- For audience, open the Audience section, click Further limit the reach of your ads and uncheck Use as a suggestion.
- For placements, exclude one placement in any ad set, or opt out of mobile or desktop devices.
- Publish and re-read the labels. The sections you changed now read Advantage+ off, and the Campaign opportunities panel stops offering the setup as applied.
Turning off the budget lever
Advantage+ campaign budget means Meta holds one budget and moves spend between ad sets as opportunities appear. To leave it, you give each ad set its own budget, and the label flips only with two or more ad sets in the campaign; a lone ad set behaves the same as an ad set budget, so Meta keeps the campaign level setup.
Optional minimum and maximum spending limits do not turn the lever off. They are still useful inside Advantage+ campaign budget when you want a floor or a ceiling on one ad set, so use them if the goal is a guard rail rather than control.
The trade is straightforward. Ad set budgets let you starve a weak ad set on purpose and test a new audience at a fixed spend, while Meta’s split will keep funding what its model likes. What you lose is the continuous reallocation that makes scaling simple. The full set of differences sits in the Advantage+ leads campaign guide.
Turning off the audience lever
Advantage+ audience treats most of your targeting as a suggestion. Age and gender, detailed targeting, and the custom or lookalike audiences you add as suggestions all become a starting point that Meta’s model can move beyond when it expects a better result.
Four inputs stay as hard controls even with the lever on: locations, minimum age, languages, and the custom audiences you exclude. Two edits that feel like they should turn the automation off do not:
- Raising the minimum age up to 25.
- Excluding a custom audience.
The setting that usually turns the lever off is the one under Further limit the reach of your ads, where unchecking Use as a suggestion means the targeting you enter is the targeting that runs. Meta also warns that you cannot exclude a lookalike audience while Advantage+ audience is on.
Retargeting is the clean case for switching it off. A campaign aimed at past visitors or at old leads needs a hard custom audience, and Meta itself does not recommend the Advantage+ audience setting for that job. For a cold, broad offer, switching it off mostly removes reach you were not paying extra for.
Turning off the placements lever
Placement exclusions sit per ad set, so excluding one placement in any ad set is enough to turn the lever off for the campaign. Meta is also gradually removing this option from ad sets in Leads campaigns. Where it has gone, placements stay on Advantage+ and the only remaining route is the account level settings described below, which cover a short list: Audience Network, Facebook Marketplace and the Facebook right column.
That matters when a placement’s cost per lead looks acceptable but its leads never qualify. Prove it on your own CRM data rather than on the average, then decide whether the placement list you can still edit covers the case. If it does not, the campaign stays in the Advantage+ setup and the fix has to come from creative, the offer or the form.
What ad account settings do and do not change
The advertising settings of the ad account hold restrictions that apply to every campaign: the locations you advertise in, a minimum age, audiences excluded for brand protection or to keep ads from your own staff, and the same short placement list. Two details catch people out. Changes can take up to 48 hours to reach existing campaigns, and the controls do not apply to ads in a Special Ad Category.
What they never do is turn Advantage+ off. Meta states that account controls leave a campaign’s Advantage+ state untouched, which is why an exclusion added there can appear to have no effect on the label.
Turning it back on
To return to the full setup, open the Campaign opportunities panel and click Apply now, or undo the lever you changed: campaign budget back on, Use as a suggestion checked again, the excluded placement restored. Meta’s own tests put the automated setup ahead on cost per lead, so the decision deserves a comparison rather than a default. Run the manual structure for the length of a fair test, and judge it on leads that reached your CRM, not on the reported number alone.
That last point is where a manual campaign gets hard to read. Once budget, audience and placement are three separate decisions, each combination of creative and landing page can carry a very different cost per lead, and Meta’s reported figure tells you nothing about which one delivered. DropCPL measures the real cost per lead of every creative and landing page pair through first-party tracking on your own landing page, so a campaign you switch out of Advantage+ still has a number you can act on.
A short checklist
- Is the lever you are changing tied to a constraint you can prove, such as retargeting or a placement with bad leads?
- Does the campaign hold at least two ad sets if you are switching to ad set budgets?
- Have you unchecked Use as a suggestion, and not only edited the audience?
- Is the placement you want to exclude still editable at ad set level in a Leads campaign?
- Will you judge the change on leads that reached the CRM over a full test window?